• Construction Grade Silicone Sealant
  • Glazing Grade Silicone Sealant
  • Sanitary Grade Silicone Sealant
  • Acrylic Sealant
  • Polyurethane Sealant
  •  
     
     
     
  • ABC Zemgrout
  • - (Machinery Grout)
  • ABC Floor Hardener
  • ABC Self-leveling Mortar
  •  
  • Thermoshield
  • - (Heat Insulating Mortar)
       
     
  • ABC Gypsum Compound
  • ABC Gypsum Putty
  • Zemcoat
  • - (Skimcoat)
  • Zembond
  • - (Acrylic Mortar and Plaster Aid)
       
       
     
     
     
     
    tiling


    ABC TILE ADHESIVE is a cement-based adhesive designed for bonding ceramic wall and floor tiles, marble, granite and natural stones on concrete surfaces. Only the highest quality portland cement, natural sand fillers and chemical additives are used. When using ABC TILE ADHESIVE, the thin-bed method is applied for faster and better looking tile installation.

    uses:
    Prevents tile cracks, bonding failure and efflorescence

    • High adhesive tensile strength
    • Non-sag and high initial adhesiveness
    • Greater workability due to long pot life and open time
    • Applicable in interior and exterior areas
    • Higher productivity per worker per day

    surface preparation:
    The substrate must be fully cured, structurally stable and level, smooth, clean and free from dirt, dust, loose material, oils, chemicals and other contaminants. Acid etch or abrade to ensure proper bonding.

    mixing:
    Into a plastic pail containing clean tap water, pour a sufficient quantity of ABC TILE ADHESIVE that may be used within the pot life of 3-4 hrs. 5 kg of ABC TILE ADHESIVE needs approx. 1.5 L of water and 25 kg needs approx. 8 L of water. Stir with a mixing device or by hand. Wait 15 min. and mix again briefly. ABC TILE ADHESIVE is now ready to use. This mix will be usable within 1-2 hrs.
    caution: Use only plastic pail or galvanized iron sheet as mixing base. Never use absorbent material such as plywood, wooden box, gypsum board, etc.

    application:

    1. Wet the substrate lightly before applying tile adhesive especially during hot and windy conditions.
    2. Spread the adhesive mortar over 1m2 area at a time using a notched trowel (available from ABC or its dealers).
    3. Fix tiles immediately within the adhesive's open time of 15 min. Adjust and align accordingly. Carry out random checks every 5 m2 to determine whether the back of the tiles are fully covered with tile ABC TILE ADHESIVE. Also check if the tile adhesive mortar still adheres to your fingers. If not, remove the adhesive layer and throw away. Do not mix with a newly prepared batch of tile adhesive mortar.

    special applications:
    For tile installations over non-concrete surfaces, such as existing ceramic tiles, gypsum boards, fiber cement boards, granolithic floors, marble, granite or wood, use ABC TILE ADHESIVE in combination with ABC REDIFIX or ABC TILE ADHESIVE HEAVY-DUTY. Consult your ABC representative or dealer for more information.

    do's and don'ts:
    Use only clean plastic pail or galvanized iron sheet and other non-absorptive material as mixing base. Use only clean water. Don’t use saline water. Do not mix newly prepared tile adhesive with an old mix to extend pot life. Dampen substrates lightly before applying and spreading tile adhesive especially during hot or windy conditions. For best results, dip tiles lightly in water and stack vertically to remove excess water before installation. Observe the 15 min. open time of ABC TILE ADHESIVE to ensure that tiles are not laid on material that has lost its adhesive power. Use ABC REDIFIX for heavy-duty tile fixing and for tile installation on existing tiles, granolithic floors, marble, plywood, gypsum and fiber cement boards and other non-concrete materials and substrates. Do not damp the whole pail of mixed tile adhesive on the floor. Let the mix remain inside the pail and apply only on a 1-2 m2 area at a time.

    safety:
    Non-toxic. However, as with any cementitious material, avoid prolonged skin contact.

    storage:
    Store in a cool dry place. When stored as directed, ABC TILE ADHESIVE will remain usable for a period of one year from date of manufacture.

    packaging:
    25 kg self-sealing multi-ply paper bag with polyethylene plastic liner

    cleaning:
    Remove excess mortar on tile face and on tools using clean water.

    coverage:
    Dependent on substrate conditions 25 kg of ABC TILE ADHESIVE shall cover approx. 5-7 m2.


      back to top  


    ABC TILE ADHESIVE HEAVY DUTY is a polymer modified adhesive, primarily designed for outdoor application and tile-over-tile installation. ABC TILE ADHESIVE HEAVY DUTY is a variation of ABC’s standard TILE ADHESIVE with the addition of advanced acrylic polymer modifiers to ensure a flexible adhesive bed and an even higher bonding strength.

    uses:

    • for installation on plywood, gypsum board and other non-concrete materials and substrates
    • for vertical or overhead installations such as facades and other outdoor areas
    • for dense tiles such as vitrified, homogenous and granite tiles
    • for commercial tile installations and industrial sites pedestrian traffic is heavy such as warehouses, parking areas, garages or factory floors

    surface preparation:
    The substrate must be fully cured, structurally stable and level, smooth, clean and free from dirt, dust, loose material, oils, chemicals and other contaminants. Acid, etch or abrade (roughen the bonding surfaces) to ensure proper bonding.

    mixing:
    Into a plastic pail containing clean tap water, pour a sufficient quantity of ABC TILE ADHESIVE HEAVY-DUTY that may be used within the pot life of 3-4 hrs. 25 kg of ABC TILE ADHESIVE HEAVY-DUTY needs approx. 8 liters of water. Stir with a mixing device or by hand. Wait 15 min., then mix again briefly and ABC TILE ADHESIVE is now ready for use. POT LIFE: 3 - 4 hrs. OPEN TIME: 15 minutes
    caution: Use only plastic pail or galvanized iron sheet as mixing base. Never use absorbent material such as plywood, wooden box, gypsum board, etc.

    application:

    1. Wet the substrate lightly before applying TILE ADHESIVE HEAVY-DUTY especially during hot and windy conditions.
    2. Spread the adhesive mortar over 1 m2 area at a time and comb with a special notched trowel (available at your ABC dealer or representative). Fix the tiles immediately within the adhesive’s open time of 15 min.
    3. Adjust and align accordingly. Carry out random checks every 5 m2 to determine whether the back of the tiles are fully covered with adhesive. Also check if the tile adhesive mortar still adheres to your fingers. If not, remove the adhesive layer and throw away.
      caution: Do not add newly prepared batch of TILE ADHESIVE HEAVY-DUTY with an old mix.
    For tile-over-tile installations on walls, consult your ABC dealer or representative.

    do's and don'ts:
    Use only clean plastic pail or galvanized iron sheet and other non-absorptive material as mixing base. Use only clean tap water. Don’t use saline water. Do not mix newly prepared ABC TILE ADHESIVE HEAVY-DUTY with an old mix to extend pot life. Dampen substrates lightly before applying and spreading TILE ADHESIVE especially during hot or windy conditions. For best results, dip tiles lightly in water and stack vertically to remove excess water before installation. Observe the 15 min. open time of ABC TILE ADHESIVE HEAVY-DUTY to ensure that tiles are not laid on material that has lost its adhesive power. Spread ABC TILE ADHESIVE HEAVY-DUTY 1 - 2 m2 at a time and install tiles not to exceed the 15 minutes open time.

    safety:
    Non-toxic. However, as with any cementitious material, avoid prolonged skin contact.

    storage:
    When stored in a cool and dry place ABC TILE ADHESIVE HEAVY-DUTY will remain usable for a period of one year from date of manufacture.

    packaging:
    25 kg multi-ply paper bag with polyethylene plastic liner

    cleaning:
    Remove excess mortar on tile face and on tools using clean water.

    coverage:
    25kg of Tile Adhesive Heavy Duty will cover approx. 5-7 m2.


      back to top  


    Baufix tile adhesive is an economical dry-set adhesive mortar specifically designed for installing natural ceramic tiles or stone slabs on floors. This special blend of portland cement, carefully selected fillers and chemical additives result in a mortar with excellent bonding and workability.

    advantages:

    • Suitable for large format tiles.
    • Prevents cracks and bonding failure.
    • High adhesive tensile strength.
    • Good workability due to long pot life and open time.
    • Applicable in interior and exterior areas.
    • Easy installation

    uses:

    1. For installations of semi-vitreous and non-vitreous ceramic tiles, as well as marble, granite and natural stones.
    2. For use over concrete surfaces only, do not apply on other substrates like plywood, gypsum boards etc.

    restrictions:
    Do not apply on substrates other than concrete (such as plywood, particle or chipboard, fiber cement boards, gypsum boards, etc.). Do not use in areas where tiles will be fully immersed in water, such as swimming pools. Use ABC TILE ADHESIVE and ABC REDIFIX for heavy duty tile fixing on granolithic, marble, existing tiles, plywood, gypsum board and other non- concrete substrates.

    surface preparation:
    The substrate must be fully cured (wood floated or light broom finished concrete), structurally sound and level, clean and free from dirt, loose material, oils and other contaminants.

    mixing:
    Pour a sufficient amount of Baufix tile adhesive into a plastic pail containing clean tap water. A 25kg bag of Baufix tile adhesive will need approx. 8L of water.
    caution: Use only a plastic pail or a galvanized iron sheet as mixing base. Never use absorptive material such as plywood, concrete floor, gypsum board etc. Stir with a mixing device or by hand. Wait 10 minutes and remix briefly. The Baufix tile adhesive is now ready for use. This mixture will be usable for 3 hours.

    application:

    1. Wet the substrate lightly before applying Baufix tile adhesive, especially during hot or windy conditions.
    2. Spread the adhesive mortar over an area of 1m2 at a time using a 6mm x 6mm x 10 mm notched trowels. Fix the tiles immediately within the adhesive open time of 15 minutes.
    3. Adjust and align accordingly. Carry out random checks every 5m2 to determine whether the back of the tile is fully covered with adhesive. Also check if the adhesive mortar still adheres to your fingers. If not, remove the adhesive layer and throw away. Do not mix with newly prepared batch of tile adhesive mortar.

    do's and don'ts:

    1. Use only a clean plastic pail or a galvanized iron sheet and other non-absorptive material as mixing base.
    2. Use only clean water. Do not use saline water.
    3. Do not mix newly prepared tile adhesive with an old mix to extend pot life.
    4. Dampen substrates lightly before applying and spreading adhesive (especially during hot or windy conditions).
    5. Do not dump the whole mix of Baufix tile adhesive on the floor. Let the mix remain inside the pail and apply on area of 1 – 2m2 at a time.
    6. Observe the 15 minutes open time of the adhesive to ensure that tiles are not laid on material that has lost its adhesive power.

    safety:
    Non-toxic. However as with any cementitious material, avoid prolonged skin contact.

    storage:
    Store in a cool dry place. When stored as directed, Baufix will remain usable for a period of 12 months from date of manufacture.

    packaging:
    25kg self-sealing multi-ply paper bag with polyethylene plastic liner.

    cleaning:
    Remove excess mortar on tile faces and on tools using clean water.

    consumption:
    Dependent on substrate conditions, a 25kg bag of Baufix tile adhesive shall cover approx. 5 – 7m2.


      back to top  


    REDIFIX is formulated for heavy-duty tile fixing as an additive to ABC TILE ADHESIVE for tile installation on existing floors and other non-concrete substrates. REDIFIX is also suitable as plaster aid. It enhances patching mortar, industrial topping, keying and other masonry works.

    advantages:

    • Promotes higher adhesive tensile strength
    • Increases compressive and flexural strengths of mortar mixes without affecting their thixotropy
    • Applicable indoors and outdoors
    • Improves Wet Service abrasion resistance of floors

    application:
    When used on Tile-Over-Tile Installation:

    The 2-Step preparation method of REDIFIX Primer and REDIFIX-modified ABC TILE ADHESIVE is required for tile installation over old tiles, marble or granite, granolithic floors, fiber cement boards, gypsum boards or any other non-concrete substrates.

    Mix thoroughly and apply immediately using a stiff brush on the existing tile substrate. Let dry for at least
    2-3 hours or overnight for best results, before any application of tile adhesive can be done.
    Coverage: approximately 8m2

    Apply the REDIFIX-modified ABC TILE ADHESIVE immediately using the recommended size notched trowel. Take extra care on the open time & pot life. CAUTION: If open time has lapsed, skinning and premature curing will occur. Coverage: Dependent on tile size, substrate condition and application thickness, it covers approximately 5-7m2.

    Refer to ABC TILE ADHESIVE packaging or technical leaflet for proper mixing and application procedures.

    When used as a Keying Aid:

    Dilute REDIFIX with clean water at a ratio of 1:1. Add 26L of this REDIFIX-water mixture to 40kg of portland cement. Apply immediately using a stiff brush.

    surface preparation:
    For existing marble or granolithic floors, remove wax by using a mild acid solution and wash thoroughly.Alsocheck for the structural soundness of existing floor. Remove loose particles, dirt and grease, form oil and other contaminants that will affect bonding. For walls, abrade paint.

    safety:
    Avoid eye splash and prolonged skin contact. In case of accidental eye exposure, wash liberally with clean water.

    storage:
    Store away from heat to avoid deterioration. In its original packaging, REDIFIX remains usable for 12 months from date of manufacture.

    packaging:
    1L and 4L plastic container


      back to top  


    ABC TILE GROUT is high quality ceramic tile joint filler. It is formulated to ensure a professional finish. Prior to grouting tiles should be installed using ABC TILE ADHESIVE. Recommended tile spacing for Regular and Tile Grout with Bio-Tech System is 3-6mm and for Sanded Grout is 7-19mm. (click here for the Color Chart)

    advantages:

    • Uniform color
    • Non-fading
    • Crack-free
    • Molds and mildew resistant
    • Available in a range of 24 colors
    • Easy to apply

    surface preparation:
    Clean and remove excess tile adhesive, dirt, dust and other foreign matters on tile and grout lines before application of grout. Dark grout colors are recommended for floor tile applications for easy maintenance and nicer long term appearance. For wall tile grout applications, all grout colors can be used.

    mixing:
    In a pail (plastic or galvanized iron) containing clean tap water, gradually add ABC TILE GROUT and mix thoroughly. Let it stand for 15 minutes. Stir to attain a creamy, pasty consistency. 2kg of tile grout will approximately need 0.75 liter of water.
    CAUTION: Mixed ABC TILE GROUT remains usable in the pail up to 1 hour.

    application:

    1. Apply ABC TILE GROUT after installed tiles have set overnight. Dampen the tile joints but there should be no standing water on areas to be grouted.
    2. Spread the paste diagonally across the tile joints using a rubber-faced float. Apply enough pressure to fill the joints uniformly.
    3. After about 5 minutes when the residue begins to form a haze, remove excess grout with the use of a wet sponge with the same diagonal strokes.
    4. Wipe off any remaining residue with a clean, soft and dry cloth to reveal the tiles’ true color and texture.
    5. Protect the grouted areas and open to foot traffic only after 24 hours.

    special applications:
    For extra grout protection apply ABC GROUT SEALER after the grout has cured for 24 hours to protect the grout joints from stains, dirt, grease and other contaminants, for easy maintenance and to keep your floors and walls looking their best.

    Use ABC GROUT WATERPROOFING additive for special applications like swimming pools, bathrooms and kitchens and other areas where the installed tiles are permanently or frequently immersed in water. This will make grouts more durable, harder and highly stain resistant against contaminants for a maintenance free floors and walls.

    For wide gap grouting applications (6mm-19mm) use ABC Sanded Grout, which is available in 5 colors.

    do's and don'ts:
    Use a clean plastic pail, a galvanized iron sheet, or any non-absorptive material as mixing base. Dampen the joints of tiles. Use clean water only. Don’t use saline water. Do not use newly prepared grout paste with an old mix to extend pot life. Do not use acid or other harsh chemicals to remove excess grout on tile surfaces.

    safety:
    Non-toxic. However, as with any cementitious material, avoid prolonged skin contact.

    storage:
    When stored in cool and dry place, ABC TILE GROUT will remain usable for 1 year from date of manufacture.

    packaging:

    • 2 kg stand-up pouch
    • 2 kg plastic bag
    • 5 kg plastic bag
    • 25 kg multi-layered self-sealing paper bag

    coverage:
    2 kg of ABC TILE GROUT can approx. cover 4 - 5 m2 depending on size and installation of tiles and 5 kg can cover approx. 10 - 12 m2.


      back to top  


    ABC TILE GROUT WATERPROOFING is an acrylic based additive. It is pre-dosed for direct mixing with ABC TILE GROUT.

    uses:
    For applications on swimming pools, bathrooms, kitchen floors and counters and other areas where installed tiles are permanently or frequently immersed in water.

    advantages:

    • makes grout water resistant, stain resistant and more durable for easy maintenance
    • enhances the color of the applied grout
    • greatly improves the bonding/flexural strength and abrasion resistance of grout

    mixing:
    1kg of ABC TILE GROUT needs approx. 0.32 - 0.33 liter of ABC GROUT WATERPROOFING. Shake well before use. Pour waterproofing liquid in a plastic container and slowly add the tile grout powder. Let it stand for 5-10 minutes. Stir to attain a workable, pasty consistency. After remix, it is ready for use.
    caution: Mix in small quantities only since it has a short open time. Do not add water. Exact dosage is critical.
    consumption:

    • A 2kg bag of tile grout will need approx. 0.64 - 0.66L of ABC GROUT WATERPROOFING.
    • A 5kg bag of tile grout will need approx. 1.6 - 1.65L of GROUT WATERPROOFING.

    application:

    1. Before application, remove any excess tile adhesive or loose particles from joints between tiles.
    2. With a narrow spatula, apply the mixture preferably along the grout lines only.
    3. Apply the tile grout waterproofing mixture 1-2m2 at a time. Do not let grout waterproofing set on tiles longer than 5 minutes, since the residue will be very difficult to remove.
    4. Remove haze and residue on tiles with a wet sponge, ensuring the desired width and depth of the grout is achieved. Wipe off any remaining residue on tiles with a clean, soft cloth.

    safety:
    Avoid eye splash and prolonged skin contact. In case of accidental eye exposure wash liberally with clean water.

    storage:
    Store away from heat to avoid deterioration. In its original packaging, it remains usable for 1 year from date of manufacture.

    packaging:
    1.8L plastic container


      back to top  


    ABC GROUT SEALER is a colorless silicone based ready-to-use penetrating formula that protects grout joints from stains, dirt, grease, mildew growth and other contaminants. It makes the cementitious tile grout water resistant for easy maintenance.

    advantages:

    • Preserves and enhances grout properties and its natural appearance
    • Protection against mildew growth
    • Easy application

    uses:

    • For interior areas such as foyer, living, dining and laundry room
    • For exterior areas such as lanai, carport, walkway and swimming pool

    surface preparation:
    Tile grout should have cured for a minimum of 12 hours prior to ABC GROUT SEALER application. Surface must be clean and free from dirt and loose materials.

    application:
    Newly applied grout needs to cure overnight before ABC GROUT SEALER can be applied. Ensure that surfaces are free from contaminants. Use a suitable brush for application (see picture). Clean tile surfaces immediately after application. Do not allow ABC GROUT SEALER to dry on tiles. Wait approx. 2 hours before applying droplets of water to test absorption. If needed, apply another coat. Allow foot traffic only after 24 hours.

    safety:
    Non-toxic. Avoid skin contact.

    storage:
    When stored in a cool dry place, it will remain usable for a period of 1 year from date of manufacture.

    packaging:
    250 ml and 1L plastic bottle

    coverage:
    1 liter approx. covers 50 m2 of grouted area. Width and porosity of grout can affect the consumption rate.


      back to top  


    ABC MULTIBOND is a water-based vinyl tile adhesive. ABC MULTIBOND is using advanced polymer technology ensures high bonding strength and ease of application. ABC MULTIBOND can avoid vinyl shrinkage, blistering and curled edges.

    properties:

    • Waterproof. Will not de-laminate even under prolonged exposure to water
    • High adhesive strength. Higher than contact cement or PVAC
    • Trowellable consistency
    • Easy to apply
    • Long open time
    • Also applicable in installing wood parquet tiles
    • Will avoid vinyl tile shrinkage, blistering and curled edges

    application:

    1. Spread ABC MULTIBOND over the surface and comb with a notched trowel preferably with a tooth size of 3 mm or even less. Please check with your ABC dealer or sales representative if you should have difficulty of in getting a notched trowel.
    2. After 15 min., fix vinyl tile, positioning each tile precisely before tamping with a rubber faced float.
      caution: ABC MULTIBOND is not designed for ceramic tile installation. While ABC MULTIBOND is waterproof, it is NOT recommended in areas subjected to continuous water immersion, as in swimming pools.

    storage/shelf life:
    When stored in a cool dry place and in its original packaging ABC MULTIBOND will remain usable for a period of 6 months from date of manufacture.

    packaging:
    4 kg plastic container

    cleaning:
    Clean tools and surfaces with water immediately after use. Do not allow excess material to set.

    coverage:
    4 kg of ABC MULTIBOND will cover approx. 10-12 m2 using a 3 mm x 3 mm notched trowels. Actual consumption will depend on substrate preparation, type of floor and notched trowel size.